電子煙注油技巧與注油常識
電子煙注油技巧與注油常識
Vape E-liquid Refilling Tips & Best Practices
1. 了解你的設備類型
Know Your Device Type
Know Your Device Type
電子煙的結構不同，注油方式也會略有差異：
Different devices have different structures, so refilling methods may vary slightly.
小煙／POD 系統（Pod Systems）
多數為封閉式或半開放式煙彈，注油需打開矽膠塞。
Closed or semi-open pod systems require opening a silicone plug to refill.
大煙／盒子主機與霧化器（Box Mods with Atomizers）
通常採用上注式（Top Fill），需旋開霧化器上蓋。
Typically top-fill design; twist open the top cap to refill.
Different devices have different structures, so refilling methods may vary slightly.
小煙／POD 系統（Pod Systems）
多數為封閉式或半開放式煙彈，注油需打開矽膠塞。
Closed or semi-open pod systems require opening a silicone plug to refill.
大煙／盒子主機與霧化器（Box Mods with Atomizers）
通常採用上注式（Top Fill），需旋開霧化器上蓋。
Typically top-fill design; twist open the top cap to refill.
2. 注油前的準備事項
Pre-Fill Preparations
Pre-Fill Preparations
確認煙油種類： 使用與設備相容的 VG/PG 比例
Use an e-liquid with the correct VG/PG ratio compatible with your device.
查看煙芯狀態： 確保煙芯不是乾燒、已老化或焦黑
Check your coil; avoid using burned or overly used coils.
保持雙手與設備清潔
Clean hands and wipe the tank to avoid contamination.
Use an e-liquid with the correct VG/PG ratio compatible with your device.
查看煙芯狀態： 確保煙芯不是乾燒、已老化或焦黑
Check your coil; avoid using burned or overly used coils.
保持雙手與設備清潔
Clean hands and wipe the tank to avoid contamination.
3. 正確注油技巧
Proper Refilling Techniques
Proper Refilling Techniques
小煙 POD 系統：
打開煙彈矽膠塞
沿邊緣慢慢注入，不可灌入中間氣孔
注至約 80–90% 滿即可，保留空間避免壓力外漏
關緊矽膠塞並擦拭乾淨
POD Device:
Open the silicone plug
Tilt and inject e-liquid slowly along the side
Fill up to 80–90% only
Seal the plug and wipe off residue
大煙霧化器：
旋開上蓋（Top Cap）或滑蓋
沿注油孔注入，避免中心通氣孔進油
注完鎖緊上蓋，檢查是否有油漬或漏油
Box Mod Atomizers:
Unscrew or slide open the top cap
Fill via side fill ports, never through the center airflow hole
Close tightly and clean any spills
打開煙彈矽膠塞
沿邊緣慢慢注入，不可灌入中間氣孔
注至約 80–90% 滿即可，保留空間避免壓力外漏
關緊矽膠塞並擦拭乾淨
POD Device:
Open the silicone plug
Tilt and inject e-liquid slowly along the side
Fill up to 80–90% only
Seal the plug and wipe off residue
大煙霧化器：
旋開上蓋（Top Cap）或滑蓋
沿注油孔注入，避免中心通氣孔進油
注完鎖緊上蓋，檢查是否有油漬或漏油
Box Mod Atomizers:
Unscrew or slide open the top cap
Fill via side fill ports, never through the center airflow hole
Close tightly and clean any spills
4. 更換新煙芯的導油步驟
How to Prime a New Coil Properly
How to Prime a New Coil Properly
對每個導油孔滴入2~3滴煙油
安裝好後注滿油倉
靜置約5~10分鐘讓棉芯充分吸收
吸幾口不按電再啟動
Drip 2–3 drops of e-liquid into each cotton hole, let it sit 5–10 minutes before use.
安裝好後注滿油倉
靜置約5~10分鐘讓棉芯充分吸收
吸幾口不按電再啟動
Drip 2–3 drops of e-liquid into each cotton hole, let it sit 5–10 minutes before use.
5. 維持良好使用習慣
Good Refilling Habits
Good Refilling Habits
切勿讓煙油完全用乾
Always refill before the tank is empty to avoid dry hits.
每週至少清潔一次霧化器
Clean the atomizer at least once a week.
避免混用不同口味會殘留異味
Don't mix different flavors unless intended (can cause flavor ghosting).
Always refill before the tank is empty to avoid dry hits.
每週至少清潔一次霧化器
Clean the atomizer at least once a week.
避免混用不同口味會殘留異味
Don't mix different flavors unless intended (can cause flavor ghosting).
6. 常見注油錯誤與解決方法
Common Mistakes & How to Fix Them
Common Mistakes & How to Fix Them
| 問題 Issue |
可能原因 Possible Cause |
解決方法 Solution |
|---|---|---|
| 滲漏 Leaking |
注太滿／沒關緊矽膠塞 Overfilled / silicone plug not sealed |
避免過滿，確認蓋緊每個接縫 Avoid overfilling; seal all openings tightly |
| 乾燒味 Burnt Taste |
沒導油好／油量過低 Coil not primed / low e-liquid |
每一口間等待一下再吸／保持油量 Wait longer before vaping / maintain e-liquid level |
| 冒油進嘴 Spitback |
油跑進氣孔／抽太用力 Liquid entered center airflow / inhaled too hard |
重新注油，輕吸慢抽 Refill correctly and puff gently |
| 吸不到煙 No Vapor |
氣孔堵塞／煙芯壞 Airflow blocked / coil damaged |
清潔霧化器、更換煙芯 Clean atomizer or replace coil |